A "New" Stoddard 1885 Patent Dividers Variation

In an earlier post dealing with the dividers of Oscar Stoddard, I mentioned that practically every example I have appears different in construction or marking from every other example. I recently acquired an example of Stoddard's March 31,1885 patent (right-hand pair above). In this patent the leg points pivot allowing them to remain perpendicular to the surface being measured. This is a fairly uncommon tool compared to Stoddard's 1872 patent, which is the one that usually shows up for sale.

These dividers have a number of issues including a missing fine adjustment spring, a replaced wing lock thumb screw as well as replaced locking thumb screws for the pivoting lower legs. Once again, the new example shows a number of differences from the more typical example (left in photo above).

                                                    "Old"                             "New"

 
The upper, square portion of the legs in the new pair is approximately 1/2" longer than in the old pair.The wing is 90 degrees as opposed to 180 degrees in the old example. 

 The markings on the upper legs also differ. The older pair logo above is a typical three line oval found in many Stoddard dividers marked "O. STODDARD, PATD MAR 31 1885, DETROIT MICH." The marking on the lower pair is faint, but the oval has two lines with the patent date above and O. Stoddard below, with a double diamond pattern in the center. None of my other Stoddard dividers have a similar marking.

                                                    "Old"                        "New"

The middle section of the legs on the old model above have locking thumb screws that allow the lower legs to be adjusted or removed. In the new model the two leg sections are permamently locked in place. In addition, the lower legs in the old example are steel while  they are bronze/brass in the new example.

So, the questions regarding the history of Oscar Stoddard's patented dividers continue to add up. Why so many variations? Who manufactured the tools for Oscar (at a later time they were manufactured by J. Stevens A&T)?

 

A VERY Old Pair of Wooden Dividers

 A recent purchase from a Fine Tool Journal auction brought home this very interesting pair of wooden wing dividers.

                                                    

They are most likely European and, I would argue, many hundreds of years old. They would seem to predate the 1700's, so I'm guessing 1600's or quite possibly earlier. A primitive tool of that time would be very difficult to date. They are 18.5 inches in height.

Here are some closer shots of the dividers.

                                    

The hinge has three leaves with a wooden pin. The tool shows extensive decorative elements which I suspect could be a hint as to its origin. There are traces of black paint and inactive "worm" holes visible in several areas. I'm unsure of the wood type, but it is not oak.

                

The wing is iron with a wooden pin holding it to the left hand leg. There is currently no means of locking the wing in place, but there is space for a wedge where the wing passes through the right hand leg.

                

The wrought iron pins at the bottoms of  the legs show evidence of the blacksmith's hammer. They are held in place by iron ferrules.

Excuse my wishful thinking, but might this guy even be of medieval origin??

Any thoughts or insights greatly appreciated.

 Two Dominant Styles of Early English Wing Dividers.

 

 

Up until the post-civil war era most, if not all, manufactured dividers and calipers in this country were imported from England or continental Europe. Since the early 1600’s English factories and their cottage industry suppliers dominated the production of small tools (sometimes referred to as “toys” in catalogs). Two English centers for the production of dividers and calipers were Birmingham and cities in the county of Lancashire, such as Warrington. The wing dividers produced in these two centers during the late 18^th and early 19^th centuries have easily distinguishable characteristics that allow us to assign many tools to one of these production centers.                              

 

Birmingham Pattern 

                                              

 To my knowledge, dividers in this category have never been assigned a name, so I’m calling them the Birmingham pattern. These tools have six consistent characteristics that set them apart from the second category: 

-        flat, three-leaf, rule joint

-        concentric circles incised on both sides of the joint

-        one or two angled incised grooves at the top, back and sides of the leg shoulders just  below the joint

-        curved chamfers on the shoulders of the dividers above the wing

-        triangular legs in cross section

-        hip bosses (carrying the wing) with angled sides due to the chamfers    above and the triangular legs below 

Four of the eight examples in my collection have heart-shaped (“mouse ears”) wing locking nuts. Six of the eight have a decorative tip on the end of the wing. Six of the eight have wings that sweep to the right, two to the left. All are of medium size, ranging from 8.5 to 16 inches. 

Three of the four marked dividers are by known Birmingham makers: W.&C. Wynn, Benjamin Freeth and Sam Ault. Ault was active between 1767 to 1781, so this style of dividers was made since at least the mid 1700’s. The fourth pair is marked “Walker”. The Directory of American Toolmakers lists a T. Walker as making dividers in America with no dates or location given. It is possible that this is an error and the maker was, in fact, English or that Walker was American and copied the Birmingham design. A pair of Walker-marked dividers almost identical to my example appears as Fig. 13 in Kebabian and Witney’s classic American Woodworking Tools.   

Birmingham dividers appear cruder in construction compared with the Lancashire dividers described below. Possibly this resulted from their being forged from wrought iron or poorer quality steel. 

 

Lancashire (Warrington) Pattern 

                                            

 “Lancashire” is a descriptor that has been applied to tools from this English county including hacksaws, spring dividers and calipers (Salaman, Dictionary of Woodworking Tools). Dividers of this type sold in England by current tool dealers often carry the label “Warrington dividers”. Warrington is a city in Lancashire. 

The following are characteristics that distinguish these dividers: 

-        cone-shaped hinge faces

-        a flattened section of the shoulders just below the hinge

-        flat chamfers on the lower shoulders with straight sides (except the smallest examples)

-        boxy hip bosses, most with raised “pyramids” on the left side of the boss

-        wings sweeping right, usually without a decorated tip

-        simple, flat, oval wing locking nuts

-        square upper and lower legs (often with slight chamfers) 

Eight of the ten examples in my collection are marked with makers names. Three of these are Warrington makers: Thewlis, Plumpton and Edelstein & Son. My examples range in size from 6.5 to 16.5 inches. Smaller dividers of this period were typically friction rather than wing dividers. 

 Lancashire style dividers were also made in Germany and France and exported to England and the United States. The German examples I have by T. Hessen Bruch and Regenstein & Maller are finely crafted pieces exceeding, I would argue, the English pieces in workmanship. 

The Lancashire dividers in my collection all appear to date to the 19^th century and are made of steel while many of the Birmingham examples show mid to late 18^th century construction and appear to be made of wrought iron. Only two of my collection of Lancashire style dividers have a fine adjustment mechanism for the wing (see below), while none of the Birmingham does.

 

A Few Exceptions to the Generalizations Above 

Not surprisingly, early wing dividers often don’t fall cleanly into one of the above categories. They show elements of both the Birmingham and Lancashire patterns described above or neither. The two dividers pictured below are primarily Lancashire style, but the joint shape and chamfering are atypical.

 

                              

 

 The wing dividers shown below are by Joseph Fenn, a London maker active between 1821 and 1873. They are basically a Lancashire style tool, but with the addition of a fine adjustment wing nut on the end of the wing. Not clearly visible in the photo is a thumb screw on the backside that locks the fine adjustment in place.

 

                                         

 

George Plumpton was a Warrington maker active likely in the late 1800’s. The dividers pictured below are typical Lancashire/Warrington wing dividers, but with a rack wing mechanism that acts as a fine adjustment. This type of dividers is uncommon and difficult to find in a functional state with unbroken teeth on the wing.

                                        

 

Additional Sources:

Tools For The Trades and Crafts (Pattern Book), documentary by Kenneth D. Roberts,  Ken Roberts Publishing, Fitzwilliam, NH, 1976.

Drawing Instruments, 1580-1980, Maya Hambly, Sotheby’s Publications, London, 1988

Tools, Working Wood in Eighteenth-Century America, Gaynor & Hagedorn, Colonial Williamsburg Foundation, Williamsburg, 1993

More Multiplying Dividers to End the Year

 The year ends with these three additions to the collection. I do have a penchant for very old dividers and the pair below pair fits the bill. They are 13" long, very heavily constructed with a three-leaf hinge with rounded "caps". The hip bosses are very heavy, one with a heart-shaped locking nut. The lock nut has created a slight groove down the center of the wing from 300 to 400 years of resetting. I'm estimating  they are 17th. century or even earlier, but of course it is very hard to pinpoint age on a blacksmith-made tool. They were acquired in Ohio Amish country, so they may be of German origin. They certainly qualify as one of the oldest pair of dividers in my collection.

Next, a primitive, user-made pair of large (21") oak dividers joins the ranks of the other wooden dividers in the collection. It is fairly common in this type of wooden tool for the wing to be a simple piece of round iron stock, rather than the more typical flat wing of metal dividers. The lock nut is a simple eye bolt which passes through a supporting iron plate attached to the arm. Old, but  very hard to age.

The final pair is far younger than his older brethren above. These dividers are marked with the name of the C. S. Osborne Co. and are a 10" model number 106. These are apparently still available from the company. Osborne predominantly manufactures leather-working tools. An interesting aspect of this tool is the two point arrangement of the hinge joint. These would appear to be easier to construct than the more common interlocking arm hinge joints. The locking nut is crude, but does show up on some examples of this model although a more solid nut is more common.

I'm thinking the next post of 2024 may shift gears to focus on wooden mallets, another one of my tool hoarding, excuse me, collecting weaknesses. Until then, to all a happy and healthy new year.